Contact

larryf@happy-wanderers.com

Follow

Info

Information on this website is our opinion only. This site was created to help others considering this wonderful lifestyle, and for our own use.

Many RV awnings have a common problem. They might catch the wind and billow out, or blow completely off. Our A&E 8500 Awning once caught the wind while driving down the highway. We were lucky, as all it did was billow out, then snap back into place. It did scare us. However, my dad wasn't so lucky. His awning also caught the wind while driving down the highway on a very windy day. But his was completely torn off. One of the arms also was torn from the motorhome. All he could do, while on the side of the road, was cut the awning off and leave it along side the highway.

The A&E awnings are held rolled up by two methods. There is a factory locking pawl located in the right end cap of the awning.  The other thing preventing the awning from unrolling is the tension on the springs. The locking arms DO NOT prevent the awning from coming unrolled. The arms are there for when the awning is rolled out, not when rolled in. 

I've found a couple after-market devices available to help prevent the unintentional unrolling.  They normally sell for about $60. I have friends who use them, and say they do work. But I found instructions on making your own awning lock for under $15. I thought I'd give it a try. The following A&E awning lock cost me $28 for two (front and rear), and took about 30 minutes. I'm not familiar with other brands of awnings, but perhaps this might work on them as well.

PARTS:

The following parts were mostly purchased at Home Depot. My local Home Depot didn't carry this type of spring anymore, but the True Value HAwning Lock Partsardware store did.
Parts requires per each awning lock:
* One 4" hose clamp
* Two "S" hooks (must fit into chain - I used 1" hooks)
* One heavy-duty picture hanger (see picture)
* One spring used on screen doors

* 6' of small linked chain
* 6' of clear vinyl tubing (large enough to fit over chain)

INSTALLATION:

First, mark the rivet that holds on the end cap that is on the outside when the awning is in the up and locked position.  This is so you will know where to install the picture hanger in the next step.  Then open the awning and clamp the heavy duty picture hanger to the end cap using the stainless steel clamp.  The hanger isAwning Lock placed with its bottom end just above the head of the outside rivet that you marked Awning Lock Hookearlier.  This prevents it from slipping around the end cap when the spring pulls down on it.  Tightening the stainless steel hose clamp forms the tab on the hanger around the curvature of the end cap.  After the clamp is tightened, use a screwdriver and bend the hanger away from the clamp enough to allow the S hook to go through the opening.

Attach a "S" hook on one end of the spring, and the chain directly to the spring on the other end.  My spring had a bracket already attached on one end, which was easily cut off with a hack saw. The spring also comes apart, allowing the chain to be looped onto it.

This picture shows the spring assembly with the awning rolled down. This was for the picture only. Normally, the spring assembly is removed from the hook before the awning is rolled down.

With the awning rolled up, the spring is attached to the hook using the awning rod. From the ground, hook the "S" hook over the rod and hold it into place on the rod by pulling on the chain as you raise it and hook it onto the picture hanger. Once hooked and the chain is hanging down, cut the chain right before it touches the awning foot.

Awning Lock AssemblyTo reduce noise and prevent scratches to your rig, slip the vinyl tubing over Awning Lockthe chain andAwning Lock Bottom cut to the correct length. On the end of the chain near the awning foot, attach another "S" hook. To prevent the "S" hooks from from falling off, use pliers to squeeze the end attached to the spring or chain. Hook this bottom "S" hook to the hole on your awning's foot. The chain should be tight, with slight tension on the spring. This length of chain prevents the awning from opening with the spring absorbing the shock, even if you try to open it manually.

OPERATION:

For traveling, roll up the awning as normal. From the ground, hook the "S" hook on the spring over the rod and hold it into place on the rod by pulling on the chain as you raise it and hook it onto the picture hanger. Gently pull on the chain and hook the the "S" hook on the chain to the hole in your awning's foot. Viola! You have an awning lock!

Latest Blogs

17 October 2023
Travel
2023 Travels
United Kingdom
October 17, 2023 - When we start thinking of another large adventure, we are always concerned about the expense. I greatly appreciate it when other people share their cost breakdown, allowing us to better plan our own trip. If we've inspired you...
07 October 2023
Travel
2023 Travels
United Kingdom
London, England October 2, 2023 - We made a straight drive today for 4+ hours. Our only stop was for a few groceries and lunch. We arrived back at the Lee Valley Camping and Caravan Park in London, which is where we spent our first night. £30 ($38 US...
06 October 2023
Travel
2023 Travels
United Kingdom
Edinburgh, Scotland September 29, 2023 - Our second day in Edinburgh was spent riding buses! Yesterday, we had purchased a 48-hour pass on the hop-on hop-off bus system that gave us access to 3 different bus lines and admission to the Edinburgh ...
29 September 2023
Travel
2023 Travels
United Kingdom
Durness, NC500, Scotland  September 22, 2023 - Our second day at Sango Sands Oasis Campsite was spent relaxing. It's been raining all day, but we still ventured out to explore the nearby Smoo Cave. Smoo Cave is an active cave being fed by t...
21 September 2023
Travel
2023 Travels
United Kingdom
Wow, time has been flying by. We have 2 weeks left in Scotland, and a week to get back to London for our flight out. We've been really lucky on the weather. The cruise was fantastic weather, with a couple cloudy mornings when at sea. We did get ...